VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  THC Vape  /  THC Vape production basics guide
THC vape products · distributors

THC Vape production basics guide

Ordering THC vape is not difficult. Ordering THC vape that sell through without a return queue behind them is the part most buyers underestimate, and it is where we spend our time. We supply distributors in European and North American markets with core lines that turn over predictably, and we keep the specification list short enough for your team to actually manage.

Published 29 September 2025  ·  VapeWholesaleHub  ·  Reading time 5 min

Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Bulk packing station during the run for a distributors order.
Bulk packing station during the run for a distributors order.

Unit price versus landed cost

Buyers come to us for THC vape after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for distributors.

The cheapest way to lower your cost per unit is usually to remove a SKU, not to negotiate a discount. Fewer lines means larger runs, fewer changeovers and a better price at the same quality.

A landed cost sheet for THC vape has five lines: unit price, packaging, freight, duty and the cost of defects. Quoting only the first line is how buyers end up surprised at the fourth.

Where defects actually come from

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

For distributors, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Lead times, freight and landed cost

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

Documentation travels with the goods: commercial invoice, packing list, and the certificate set for your market. We send a scanned copy before dispatch so your broker can clear the file in advance.

  • Reference sample retained from every batch
  • Private label files archived for future rebrands
  • Mixed SKU cartons to spread first-order risk
  • Document pack prepared per destination market
  • Batch codes traceable from carton back to production date
  • Standing reorder schedule with a fixed cut-off

What happens when something goes wrong

Every account gets a named contact who has actually seen the product. Being passed between three people to answer one question about a coil resistance is the fastest way to lose a buyer, so we do not organise support that way.

The replacement policy is deliberately simple: report within seven days of delivery with photos and the batch code, and we replace or credit at the next shipment. We do not argue about a defect we can see in a photograph.

Specification summary

Typical specification for this category
Volume0.5 ml
HardwareCotton core
Thread510 thread
AirflowFixed
WindowFull glass
PackagingTube
Minimum order50 units per SKU, mixed cartons allowed
Lead time22 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

Can you ship to multiple locations?

Yes. Split shipments are quoted separately because consolidation and splitting price differently. Tell us the destination list at quotation stage and we will show both options.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

Related reading

Need a quotation on THC vape products?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on THC vape products

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us